Steel Coil Slitting Calculator — Tube, ERW Pipe & Sheet Weight

Know what a coil will make before it is slit

Work out strip width, slits, tube and ERW pipe weight, cut sheets and scrap for any mother coil. Then send the numbers to us for a quote.

Example: a 1220 mm coil cut into six 197.5 mm strips for 50×50 tube leaves 35 mm of side scrap.

Coil calculator

Enter your coil once, then switch between tube, pipe, sheet and the slitting optimizer. Results update as you type.

Step 1. Your mother coilUsed by every tab below.

Carbon steel default 7.85
Slitting: Tube, Pipe & Optimizer
Width lost between adjacent strips

Step 2. Tube size

e.g. 50×50, 60×30, 40 20
Blank = 2 × thickness
Head/tail ends, mill setup, cut-off. Side scrap is separate.
Total tubes output——
Weight per piece——
Slits across width——
Scrap, loss & allowance——
Slitting pattern across the coil—
Tube stripsEdge trim + side off-cut

Strip width and weight details

Material balance (every kg counted once)

Itemkg% of coil

Step 2. Pipe size

Added to π × (OD − t). Mill-specific — enter yours.
Used only when basis = mill-approved
Head/tail ends, setup, cut-off. Side scrap is separate.
Total pipes output——
Weight per pipe——
Slits across coil——
Scrap, loss & allowance——
Slitting pattern across the coil—
Pipe stripsEdge trim + side off-cut

Theoretical vs mill strip width

Material balance (every kg counted once)

Itemkg% of coil

Step 2. Sheet size

0 = mill edge kept (sheet width = coil width)
Total cut sheets——
Weight per sheet——
Coil linear length——
Remaining coil weight——

Material balance (every kg counted once)

Itemkg% of coil

Mixed-size slitting optimizer

Method: exact bounded enumeration (depth-first search) of every maximal slitting pattern that can be built from the selected strip widths within your lane, knife-gap, edge-trim and size-mix limits. Patterns are ranked by smallest remaining width. This is deterministic mathematics — not artificial intelligence. Uses the coil from Step 1 and the piece length and process loss from the Tube tab.

Strip widths to combine, in mm

Reference strip widths are SteelCal workshop values for thin-gauge tube and do not change with thickness. Replace them with your mill’s approved widths.
Best pattern across the coil—
RankSlitting pattern (lanes × size)LanesUsed widthResidualEfficiencyTotal pcsPieces by size

How the numbers are worked out

Every result comes from the theoretical mass of steel. Sizes are in millimetres, lengths in metres, density in g/cm³ and mass in kilograms.

Strip and sheet weight

Weight (kg) = Width (mm) × Thickness (mm) × Length (m) × Density ÷ 1000

A 1220 mm × 1.5 mm strip of carbon steel weighs 1220 × 1.5 × 1 × 7.85 ÷ 1000 = 14.37 kg per metre.

Coil length

Length (m) = Coil weight (kg) × 1000 ÷ (Width × Thickness × Density)

A 7500 kg coil, 1220 × 1.5 mm, is about 522 m long. Every slit strip runs the full length of the coil.

Slits across the coil

Slits = floor((Coil width − Edge trim + Knife gap) ÷ (Strip width + Knife gap))

Limited to your slitter’s maximum lanes. Whatever width is left, including the edge trim, is side scrap.

Square and rectangular tube

A = 2t(B + H − 2t) − (4 − π)(ro² − ri²)

The EN 10219-2 cross-section, with outer corner radius ro (2t unless you enter one) and ri = ro − t. Weight is A × Density ÷ 1000 kg/m, and the theoretical strip width is A ÷ t. Mill strip widths are usually wider because of forming and weld allowances, so plan with your mill’s figure.

ERW round pipe

kg/m = π × (OD − t) × t × Density ÷ 1000

For steel that is 0.02466 × (OD − t) × t. The theoretical strip width is the mean circumference π × (OD − t); ERW mills add an allowance for edge trimming, weld upset and sizing.

Pieces from a coil

Pieces = Slits × floor(Coil length × (1 − Process loss) ÷ Piece length)

Only the slit strips make pieces. The material balance splits the coil into finished product, allowance, side scrap, process loss and end remnant, and always adds up to the coil weight.

Cut sheets

Sheets = floor((Width − Trim) ÷ Sheet width) × floor((Length − Crops) ÷ Sheet length)

The remaining coil weight is the length left over that is too short for one more sheet.

Mixed-size slitting

The optimizer checks every combination of up to four strip widths within your lane, knife-gap and edge-trim limits, keeps only patterns where no further strip fits, and ranks them by the least width left over. It is plain arithmetic, not artificial intelligence.

Questions

How do I calculate the weight of a steel strip or sheet?

Weight (kg) = Width (mm) × Thickness (mm) × Length (m) × Density (g/cm³) ÷ 1000. For carbon steel the density is 7.85 g/cm³, so a 1220 mm × 1.5 mm strip weighs 14.37 kg per metre.

How many slits can I get from a mother coil?

Slits = floor((coil width − edge trim + knife gap) ÷ (strip width + knife gap)), limited by the slitter’s maximum number of lanes. The width left over is side scrap.

Why is the mill strip width different from the theoretical width?

The theoretical developed width is the mid-wall perimeter of the finished section. Real tube and ERW pipe mills add allowances for edge trimming, weld upset and sizing, which depend on the mill and its roll tooling. Always use the strip width approved by your mill for production planning.

Is the Zero-Waste optimizer artificial intelligence?

No. It is a deterministic mathematical search (bounded exact enumeration of maximal slitting patterns). It checks every combination of the selected strip widths within your limits and ranks them by remaining width.

Are the results exact?

No. They are theoretical estimates based on nominal dimensions. Actual weight and piece counts vary with thickness tolerance, coating, coil weight accuracy and mill practice. Confirm with your mill or supplier before ordering or quoting.