Steel Coil Slitting Calculator — Tube, ERW Pipe & Sheet Weight
Know what a coil will make before it is slit
Work out strip width, slits, tube and ERW pipe weight, cut sheets and scrap for any mother coil. Then send the numbers to us for a quote.
Coil calculator
Enter your coil once, then switch between tube, pipe, sheet and the slitting optimizer. Results update as you type.
Step 1. Your mother coilUsed by every tab below.
Step 2. Tube size
Strip width and weight details
Material balance (every kg counted once)
| Item | kg | % of coil |
|---|
Step 2. Pipe size
Theoretical vs mill strip width
Material balance (every kg counted once)
| Item | kg | % of coil |
|---|
Step 2. Sheet size
Material balance (every kg counted once)
| Item | kg | % of coil |
|---|
Mixed-size slitting optimizer
Strip widths to combine, in mm
| Rank | Slitting pattern (lanes × size) | Lanes | Used width | Residual | Efficiency | Total pcs | Pieces by size |
|---|
How the numbers are worked out
Every result comes from the theoretical mass of steel. Sizes are in millimetres, lengths in metres, density in g/cm³ and mass in kilograms.
Strip and sheet weight
Weight (kg) = Width (mm) × Thickness (mm) × Length (m) × Density ÷ 1000
A 1220 mm × 1.5 mm strip of carbon steel weighs 1220 × 1.5 × 1 × 7.85 ÷ 1000 = 14.37 kg per metre.
Coil length
Length (m) = Coil weight (kg) × 1000 ÷ (Width × Thickness × Density)
A 7500 kg coil, 1220 × 1.5 mm, is about 522 m long. Every slit strip runs the full length of the coil.
Slits across the coil
Slits = floor((Coil width − Edge trim + Knife gap) ÷ (Strip width + Knife gap))
Limited to your slitter’s maximum lanes. Whatever width is left, including the edge trim, is side scrap.
Square and rectangular tube
A = 2t(B + H − 2t) − (4 − π)(ro² − ri²)
The EN 10219-2 cross-section, with outer corner radius ro (2t unless you enter one) and ri = ro − t. Weight is A × Density ÷ 1000 kg/m, and the theoretical strip width is A ÷ t. Mill strip widths are usually wider because of forming and weld allowances, so plan with your mill’s figure.
ERW round pipe
kg/m = π × (OD − t) × t × Density ÷ 1000
For steel that is 0.02466 × (OD − t) × t. The theoretical strip width is the mean circumference π × (OD − t); ERW mills add an allowance for edge trimming, weld upset and sizing.
Pieces from a coil
Pieces = Slits × floor(Coil length × (1 − Process loss) ÷ Piece length)
Only the slit strips make pieces. The material balance splits the coil into finished product, allowance, side scrap, process loss and end remnant, and always adds up to the coil weight.
Cut sheets
Sheets = floor((Width − Trim) ÷ Sheet width) × floor((Length − Crops) ÷ Sheet length)
The remaining coil weight is the length left over that is too short for one more sheet.
Mixed-size slitting
The optimizer checks every combination of up to four strip widths within your lane, knife-gap and edge-trim limits, keeps only patterns where no further strip fits, and ranks them by the least width left over. It is plain arithmetic, not artificial intelligence.
Questions
How do I calculate the weight of a steel strip or sheet?
Weight (kg) = Width (mm) × Thickness (mm) × Length (m) × Density (g/cm³) ÷ 1000. For carbon steel the density is 7.85 g/cm³, so a 1220 mm × 1.5 mm strip weighs 14.37 kg per metre.
How many slits can I get from a mother coil?
Slits = floor((coil width − edge trim + knife gap) ÷ (strip width + knife gap)), limited by the slitter’s maximum number of lanes. The width left over is side scrap.
Why is the mill strip width different from the theoretical width?
The theoretical developed width is the mid-wall perimeter of the finished section. Real tube and ERW pipe mills add allowances for edge trimming, weld upset and sizing, which depend on the mill and its roll tooling. Always use the strip width approved by your mill for production planning.
Is the Zero-Waste optimizer artificial intelligence?
No. It is a deterministic mathematical search (bounded exact enumeration of maximal slitting patterns). It checks every combination of the selected strip widths within your limits and ranks them by remaining width.
Are the results exact?
No. They are theoretical estimates based on nominal dimensions. Actual weight and piece counts vary with thickness tolerance, coating, coil weight accuracy and mill practice. Confirm with your mill or supplier before ordering or quoting.